Sold/Expired Dan Wesson Custom Shop CCO work by Derr Precision SMOKIN DEAL

Greg6640

Fanatic
Rating - 0%
0   0   0
Joined
Sep 19, 2018
Messages
10
Good day gents,

I have only fired 50 rounds through it an put it in the safe. I am transitioning to 9mm or I might consider buying this back. I sold this to a brother gunner, he never fired a round through it.

Dean has fallen on hard times with medical bills and is facing Chapter 13. I am listing this pistol on his behalf. No monies will come to me if purchased but will go directly to Dean. I will PM you with the information to send the funds. When they clear the gun will ship from FFL to FFL.

The gun is as follows described the original owner and for the most part, is the original listing. The pictures I took a short time ago and are current. Some of the listings of parts etc are from the original post and have been edited appropriately. This is a smoking deal!! On to the good part!!
Dan Wesson Custom Shop CCO .45
Stainless steel Commander slide
Stainless steel Officer frame <-- Steel frame, not aluminum.
Ball cuts
25 LPI front strap
Undercut trigger guard
Phase II dehorn
Flush cut and reverse crown barrel
Plain black ledge rear sight
Tritium front sight
Recessed slide stop
Short trigger
3.75# trigger pull
EGW Carry Bevel bushing
EGW flat-wire .250 guide rod and spring plug
ISMI Commander flat-wire recoil spring
Wilson Bullet-Proof wide Ambi thumb safety trimmed right side lever
Wilson Bullet-Proof slide stop
Wilson Bullet-Proof Tactical mag release
Smith and Alexander arched mag well
VZ Operator II grips (Beveled and Cerakoted)

Magwell/MSH
You don't often see a mag well on a compact frame but I encourage you to try it. It only adds .25" in height but makes a big difference in feel. If you prefer no magwell or no arch a simple swap and you're set.

Derr Precision work-
Blend mag well
Line up ball cuts
Bevel bottom edge of the slide
French Borders
Beavertail knuckle relief notches (Pictured below)
Beavertail high grip mod
Reduce and blend thumb safety panels
Wilson Bullet-Proof extractor, plus spare
New EGW Carry Bevel bushing, hand-fit for optimum accuracy
Greg Derr Cerakoted it Graphite Black. after learning that stainless steel and I don't get along. If Cerakote isn't to your liking bead blast it down to the original stainless gun.

1 - Tuned WC SS Bullet-Proof spare extractor
2 - Tuned DW spare extractors
1 - DW factory EGW Carry Bevel bushing, finger tight
2 - DW 7-round factory mags
3- Tripp 7R-45-RO mags
2 - Wilson 8-round mags
2 - ISMI 22# Flat-wire Commander Recoil Spring
1 - ISMI 20# Flat-wire Commander Recoil Spring
1 - ISMI 18# Flat-wire Commander Recoil Spring
1 - 22# Wolff Conventional Recoil Spring
1 - 18# Wolff Conventional Recoil Spring
3 - Wolff Firing Pin Springs, Standard Power
3 - Wolff 23# Officer Hammer Springs
1- Wolff 22# Officer Hammer Spring
1- Wolff 21# Officer Hammer Spring
1- Wolff 20# Officer Hammer Spring
Everything is above board! Rest assured that what you see is what you get.

Sterling invested $3500 into this gun.
The price is $1800 shipped and insured. USPSMO or Certified/Teller Bank check.
First I'll take it followed by a PM to me gets it!



Thank you for looking and considering this gun.
Greg
PS: If there is a problem with me listing this gun for Dean please advise me. Thank you in advance.
4734
4735
4736
4737
4738
4739
 
Last edited:

Greg6640

Fanatic
Rating - 0%
0   0   0
Joined
Sep 19, 2018
Messages
10
Tried to edit to say that this listing is cross-posted but I was not allowed to edit for some reason.
Thank you for looking! I have a good trade rating on another forum if you need assurance as to my providence.
 

Latest posts

Top